STANDARD PLASTISOL MSDS:

Most of our QCM plastisol inks are covered by the following MSDS:

MSDS for ATP/XOLB/GL/AP/MTL/HP/QMX/PERM/OPC PRINTING PLASTISOLS (INKS)

Prepared by Roy Wheeldon _ Date 03/03/03

MATERIAL SAFETY DATA SHEET

QCM COMPANY, 930 Central Ave. South, Kent, WA 98032 Phone: (253) 859-0933

FOR EMERGENCY HAZARDS/SPILLS ONLY CALL CHEMTREC 1-800-424-9300

SECTION I. MATERIAL IDENTIFICATION

I Trade Name and Synonyms: ATP, XOLB, GL, AP, MTL, MB, OPC, PERM & QMX PRINTING PLASTISOLS

Chemical Name and Synonyms: PLASTISOLS

Chemical Family: POLYVINYL CHLORIDE

Formula: MIXTURE

SECTION II INGREDIENTS AND HAZARDS

Chemical name | % | exposure limits in air ACGIH (TLV)OSHA (PEL) other

Plastisol | | not hazardous

Organic pigments | | not hazardous

Thickener | | not hazardous

Titanium dioxide (in some formulas) | | not hazardous

SECTION III PHYSICAL DATA

Boiling point at 1 atm, deg F: 380 C WT/GAL: 11.00 LBS (AVERAGE)

Vapor pressure at (mm Hg):1.2 @ 200 C Evap. Rate ( <0.1 BuAc=1)

Vapor density (Air=1): 16 Volatiles, % by Volume: <1.0%

Water solubility:0.005% Molecular weight: MIXTURE

Appearance & Odor: VARIOUS COLORED PASTES. SLIGHT ODOR OF PLASTICIZER.

SECTION IV FIRE AND EXPLOSION DATA

Flash Point & Method: 425 F C.O.C. Autoignition Temp.: N/A

Flammability Limits in Air: N/A Upper: N/A Lower: N/A

Extinguishing Media: dry powders, carbon dioxide, chemical foam, water.

Special Fire fighting procedures: self-contained breathing apparatus.

Unusual fire and explosion hazards: toxic gases evolved when burned.

SECTION V HEALTH HAZARD INFORMATION | TLV 5 ppm

Effect of Overexposure: excessive high temperature may produce irritating vapor. during normal processing

a small amount of vapor will be evolved; respiratory problems may occur without adequate ventilation.

First aid:

Eye Contact: flush with water for 15 minutes.

Skin Contact: wash skin with soap and water.

Inhalation: if excessive fumes, remove to fresh air.

Ingestion: consult physician.

V.O.C. EMISSIONS: 0.32 lbs per gallon or 40 grams per liter (maximum); 0.32 lbs per gallon or 40 grams per liter (maximum) less water and less exempt compounds.

Primary routes of entry into the body: Skin absorption and inhalation of fumes during heat processing.

SECTION VI. REACTIVITY DATA

Stability: stable | x | Conditions to avoid: high heat will gel the material.

Incompatibility: (materials to avoid): none

Hazardous decomposition products: smoke, soot, co, co2, and HCl vapor when burned.

conditions to avoid: N/A

Hazardous Polymerization: will not occur | x |

SECTION VII. SPILL, LEAK, AND DISPOSAL PROCEDURES

Spills, leaks: (steps to be taken) treat as non-hazardous material.

Waste disposal method: Not hazardous. Check with Federal, State and Local regulations. But may be possible to cure out to solid state and landfill. Check. DO NOT landfill in wet state.

SECTION VIII. SPECIAL PROTECTION INFORMATION

Respiratory protection: (Specify Type) Not required.

Ventilation: Local exhaust: recommended during processing

Special: N/A

Mechanical (General) none

Other: N/A

Protective gloves: Recommended always to avoid skin contact.

Eye protection: not required, but Good industrial hygiene practice.

Other protective equipment and precautions: good ventilation

SECTION IX. SPECIAL PRECAUTIONS AND COMMENTS

Storage & handling information: optimum storage temperature 50 deg F. to 90 deg F.

Other precautions: during processing, ventilation is recommended. if thinners or reducers are added, hazards may increase. See msds on specific additives or call manufacturer.

Dot class: not regulated

HAZARD IDENTITY HMIS SYSTEM:

|Health | 1 |

|Flammability | 1 |

|Reactivity | 0 |

|Contact | B |

Judgments as to the suitability of information herein for purchaser's purposes are necessarily purchaser's responsibility. Therefore, although reasonable care has been taken in the preparation of such information, QCM Co. extends NO warranties, makes NO representations and assumes no responsibility as to accuracy or suitability of such information for application to purchaser's intended purposes of or for consequences of it's use.

Written by Manager of Customer and Technical Services